PCB Libraries Forum Homepage
Forum Home Forum Home > PCB Footprint Expert > Questions & Answers
  New Posts New Posts RSS Feed - Round off in footprint expert calculator
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Round off in footprint expert calculator
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
eaglor View Drop Down
New User
New User


Joined: 20 Jun 2024
Status: Offline
Points: 14 		Post Options Post Options   Thanks (1) Thanks(1)   Quote eaglor Quote  Post ReplyReply Direct Link To This Post Topic: Round off in footprint expert calculator
    Posted: 28 Aug 2024 at 10:20am
Hi All

I am using the Footprint Expert SMD Reference Calculator.xlsx. 

I have a question about the round off when calculating the footprint pad size and spacing. 

Why does it round the C(Center to Center Spacing) and X value, not the ZMax and GMin value? 

Is it compliant with IPC7351B standard?

Thanks
Back to Top
 
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5940 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 28 Aug 2024 at 10:39am
You should download and install the V24.10 Footprint Expert Calculator to get better results. 
Stay connected - follow us! X - LinkedIn
Back to Top
eaglor View Drop Down
New User
New User


Joined: 20 Jun 2024
Status: Offline
Points: 14 		Post Options Post Options   Thanks (0) Thanks(0)   Quote eaglor Quote  Post ReplyReply Direct Link To This Post Posted: 28 Aug 2024 at 10:41am
Hi Tom,

Thanks, Does the "V24.10" round the ZMax and GMin value, not the C and X value?
Back to Top
eaglor View Drop Down
New User
New User


Joined: 20 Jun 2024
Status: Offline
Points: 14 		Post Options Post Options   Thanks (1) Thanks(1)   Quote eaglor Quote  Post ReplyReply Direct Link To This Post Posted: 28 Aug 2024 at 10:44am
I am comparing the formula difference between Altium Designer and Footprint Export, just want to know which one is better? which value should be round to compliant with the B standard. 
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5940 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 28 Aug 2024 at 1:41pm
Altium uses the original 2005 IPC-7351 release. 

V24.11 Footprint Expert uses a combination of these standards and guidelines:
  • IPC-7351B (Mathematical model)
  • IPC-7352 (Pad Stack naming convention)
  • IPC J-STD-001 (Solder Joint Goals)
  • IEC 61188-7 (Zero component orientation) 
  • IPC-7093A (Solder mask defined thermal pads)
Stay connected - follow us! X - LinkedIn
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5940 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 28 Aug 2024 at 1:46pm
After calculation of a footprint, select the Footprint panel > Calculation Details. 
Stay connected - follow us! X - LinkedIn
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down



This page was generated in 0.219 seconds.